REVIEW: Cycle Country CV Boot Guards

It doesn’t take too long to learn that CV joints and boots need a little extra protection. They aren’t particularly cheap or super easy to replace, but they are often susceptible to damage. Rubber boots are easily pierced by debris on the trail allowing mud, dirt and water to penetrate the CV joints. The older the boots are the more brittle they will become. Neecy’s Polaris Hawkeye 4×4 suffered two blown CV joints within a couple of months. We replaced them with new Monster Axles, and it was was time to protect that investment with a set of CV boot guards.

Failed CV joint, causing the entire axle to come loose. We tied it out of the way with a bungee cord to finish the ride.

I picked up a set of Cycle Country CV Boot Guards (sometimes referred to as A-arm guards) off ebay. They are also are available from many retailers. The guards are very solid, made from 12 guage steel and finished with a powder coating. Not only will they protect the boot and joint, but it will also help protect the A-arm itself from damage. It is a huge upgrade from the flimsy stock plastic found on the Hawkeye from the factory.

The Cycle Country guards were super easy to install. For the Hawkeye, start by removing the two screws holding the factory guard in place. Then remove the factory guard. Next place the Cycle Country guards under the A-arms and bolt them into place with the U-bolts. As the bolts tighten up make sure the guards are in the proper spot. The guard should not come into contact with any part of the frame, bumpers, wheels or tires while stationary or while riding. Once you finish tightening them you’ll need to cut off the excess bolt sticking out below so they don’t catch on anything. After a short ride recheck the position of the guards. Readjust and tighten as needed. Checking the position of the guards should be a part of your regular maintenance plan.

Now your ride is much better protected from costly damage that can easily be found on the trails. Prices vary by application. Rear guards are also available for many applications. For more information, including a fitment chart and other accessories, see Cycle Country at http://www.cyclecountry.com.

REVIEW: RAM Mounts Aqua Box

Cell phones are a crucial item for most everyone. Trail riding is no exception to this. There have been many times when my trail buddies were trying to call me and the calls went unnoticed while I was bounding down the trails. So I was super excited to pick up a RAM Mounts Aqua Box. I have used RAM Mounts equipment in vehicles so I was familiar with the quality. I ordered the RAM-B-149Z-AQ2U from GPSCity.com. The kit contains three separate items: a handle bar mount, arm and a Medium Aqua Box. According to RAM, the internal dimensions of the medium box are 2.88″ wide, 5.75″ high and 1.188″ deep. Three foam pads of different thicknesses are included so your device is well secured inside the box. Alternative kits are made with smaller or larger Aqua Boxes. I found the medium sized Aqua Box to be perfect for my Apple iPhone 3GS in its OtterBox Defender case.
Ram Aqua Box Break Down     Assembly is a snap and took less than 10 minutes. The flex lens is not hard to install but it seems a bit awkward at first. RAM offers a video on their website to clear up any confusion. The ball joint system that RAM uses makes mounting extremely flexible. The kit includes mounting hardware for different sized handlebars.  The box is waterproof and though you can’t fully use the iPhone touchscreen through the Aqua Box flex lens, you can easily see calls and messages when they come in. Simple screen touches work fine but sliding functions do not work. The box also has a punchout that can be used to route wires from the device. The case design should maintain its water tight abilities even with this option used.
Ram Aqua Box Mounted     During an hour long trail ride, there was no movement at all from the RAM system. It held solidly in place and the safety of my iPhone was the last thing on my mind. I did panic a time or two when I realized my phone was not in my pocket, thinking it had fallen out while riding. I was quickly reassured to see it staring back at me from between the handle bars. I consider this a must have add-on for any trail rider and I will be adding it to my other quads. MSRP from RAM Mounts is $68.92. The system is covered by a lifetime warranty with the exception of the replaceable flex lens. Lenses are about $5 from RAM. You can see this and their other offerings at http://www.ram-mount.com/.


Protect your smartphone with an OtterBox!